Gipfel Engineering

Brines, Crystallising & Viscous Fluids

Brines & Viscous Fluids mechanical seal selection diagram: pump duties, seal arrangements and API piping plans

Media Overview

Brines, Crystallising & Viscous Fluids — Media Overview

Saturated brines, sugar syrups, molasses, polymers and latex fail seals in the same way: the fluid crystallises, sets or coagulates when leakage meets air or when the face film is heated and sheared. The seal design must keep the atmospheric side clean, keep the film liquid and carry the start-up torque of a viscous fluid. For plant-level selection see Wastewater, ETP & ZLD, Sugar Refinery and Polymer & Rubber.

Key Sealing Challenges

  • Crystallisation: ZLD brines and sugar syrups crystallise on the atmospheric side and lock the faces; a Plan 62 quench or a pressurised double seal is used.
  • Chlorides: high-TDS brines pit stainless steel; duplex 2507 or titanium metal parts are used.
  • Start-up torque: viscous fluids impose high break-away torque; drive collars and faces must take it, and hot fluids are pre-heated before start.
  • Setting fluids: hot-melt resins and polymers set when cold; heated seal chambers or heated barrier systems are used.
  • Shear-sensitive latex: latex coagulates in the face gap; a pressurised double seal keeps it out of the faces.

Which mechanical seal is used on ZLD evaporator brine pumps?

A pressurised double cartridge seal with sintered SiC vs sintered SiC faces, EPDM secondary seals and duplex 2507 or titanium metal parts on API Plan 53A/54 is used on crystallising brines. On lower-concentration duties a single seal with a Plan 62 water quench is used.

Root-Cause Failure Analysis — Field Example

Symptom: Forced-circulation brine pump seal sticks and leaks after every stop.
  ├── Incorrect Response: "Replace faces and restart."
  ├── Diagnostic Evidence Required:
  │     ├── Salt crystals on the atmospheric side of the faces?
  │     ├── Was the quench running during stop and restart?
  │     └── Pitting on metal parts from chlorides?
  └── Engineered Solution:
        ├── Double seal with clean barrier (Plan 53A/54), or Plan 62 quench.
        ├── Sintered SiC vs sintered SiC; EPDM.
        └── Duplex 2507 or titanium metal parts.

Frequently Asked Questions

Why is a steam or hot-water quench used on sugar syrup pumps?

Syrup leakage dries and crystallises on the atmospheric side, locking the faces at the next start. A Plan 62 quench dissolves it continuously.

How are hot-melt resin pumps sealed?

The seal chamber is heated so the resin stays liquid, and a metal bellows seal with flexible graphite or a double seal with a heated barrier is used. The pump is pre-heated before start-up. Related: ZLD · Distillery ZLD · Sugar Mill · Polymer.


Request a Seal Selection

Send the fluid name and concentration, SDS, temperature, suction and discharge pressure, pump make and model, shaft size and speed to info@gipfelengg.com or use our enquiry form. Gipfel Engineering (ISO 9001:2015, NSIC-registered MSME, Mumbai) designs and manufactures mechanical seals, seal support systems and process pumps.

Equipment solutions: Positive Displacement Pumps · Overhung Pumps · Mixers.

Pump Duty & Mechanical Seal Selection Matrix

Typical values for selection guidance only. Final selection is made against the customer duty sheet and the fluid SDS.

Pump duty Fluid Typical temp. Typical pressure (bar) Seal arrangement Faces / elastomer API piping plan
MVR / Forced-Circulation Brine Pump Saturated brine, high TDS 60–110 °C 2–6 bar Double cartridge, back-to-back (pressurised) Sintered SiC vs sintered SiC / EPDM; duplex 2507 or titanium API Plan 53A or Plan 54
Brine Transfer Pump NaCl brine Ambient–60 °C 2–5 bar Balanced multi-spring cartridge SiC vs SiC / EPDM; duplex API Plan 11 + Plan 62
Syrup / Molasses Pump Sugar syrup 65° Brix, molasses 50–80 °C 3–8 bar Balanced multi-spring cartridge SiC vs carbon or SiC vs SiC / EPDM API Plan 62 hot-water quench
Massecuite Pump Massecuite with crystals 60–75 °C 3–8 bar Double cartridge, back-to-back (pressurised) SiC vs SiC / EPDM API Plan 53A or Plan 62
Polymer / Resin Pump Resin, hot melt 120–220 °C 5–20 bar Stationary metal bellows cartridge SiC vs carbon / flexible graphite Heated seal chamber + Plan 62
Latex Pump Natural or synthetic latex Ambient–60 °C 2–6 bar Double cartridge, back-to-back (pressurised) SiC vs carbon / EPDM API Plan 53A/54

Reviewed by Gipfel Engineering’s technical team.

Technical Information Disclaimer

The information on this page, including process descriptions, flow diagrams, operating ranges, seal arrangements, materials and piping plans, is general technical guidance for information only. Values shown are typical industry ranges, not guaranteed ratings or specifications of any Gipfel Engineering product. Each application differs. Seal selection, material compatibility, installation and operation must be verified by qualified personnel against the specific equipment data sheet, process conditions, applicable codes and the pump manufacturer’s instructions. A binding recommendation is given only in a written quotation or technical offer from Gipfel Engineering.

References to standards (such as API 682, ISO 21049, ISO 3069, FDA 21 CFR 177.2600 and NACE MR0175 / ISO 15156) describe common industry practice. They do not mean that any product is certified, qualified or approved to that standard unless this is confirmed in writing for a specific order. Third-party company and product names, including “equivalent to” references, are used for identification only and remain the trademarks of their owners. No affiliation, endorsement or OEM approval is implied.

Compliance with safety, hazardous-area, environmental and statutory requirements at the user’s site remains the responsibility of the plant owner or operator. To the extent permitted by law, Gipfel Engineering accepts no liability for loss or damage arising from reliance on this general information without a confirmed written recommendation. Content may change without notice.

Table of Contents