Gipfel Engineering

Sanitary & High-Purity Fluids

Sanitary & High-Purity Fluids mechanical seal selection diagram: pump duties, seal arrangements and API piping plans

Media Overview

Sanitary & High-Purity Fluids — Media Overview

Water for injection (WFI), purified and ultrapure water, dairy, brewery and bioprocess fluids are sealed to protect the product rather than the plant. The seal must not shed particles or leach ions, must survive CIP chemicals and steam sterilisation (SIP at about 121–135 °C), and must not trap product where bacteria can grow. For plant-level selection see Pharmaceutical, Biotech & Sterile Manufacturing and Food, Dairy & Beverage.

Key Sealing Challenges

  • Particle shedding: carbon faces can shed fine particles into WFI and UPW; SiC vs SiC or diamond-coated SiC faces are used.
  • Ion leaching: UPW at 18.2 MΩ·cm picks up metal ions; wetted area is kept to a minimum and the 316L surface finish is specified per duty.
  • Cleanability: dead pockets hold product; open, drainable seal chambers with springs kept out of the product are used.
  • CIP / SIP: caustic and acid washes and 121–135 °C steam need peroxide-cured EPDM or FFKM.
  • Material documents: where FDA 21 CFR 177.2600 or USP Class VI certified elastomers are mandatory, state this at enquiry; these certificates are not supplied as standard.

Which mechanical seal is used on WFI loop pumps?

A single balanced cartridge seal of hygienic design with SiC vs SiC or diamond-coated SiC faces (no carbon shedding), peroxide-cured EPDM and 316L wetted parts is typical, in an open, drainable seal chamber. A double seal with a condensate or clean-steam barrier is used where the atmospheric side must also be sterile.

Root-Cause Failure Analysis — Field Example

Symptom: Particle counts rise in the WFI loop; black traces at the pump.
  ├── Incorrect Response: "Increase filtration."
  ├── Diagnostic Evidence Required:
  │     ├── Are the seal faces carbon (particle shedding)?
  │     ├── Is the seal chamber drainable and free of dead zones?
  │     └── Elastomer condition after SIP cycles.
  └── Engineered Solution:
        ├── SiC vs SiC or diamond-coated SiC faces.
        ├── Peroxide-cured EPDM rated for SIP.
        └── Open, drainable seal chamber.

Frequently Asked Questions

Why are diamond-coated faces used in pharma water?

Diamond-coated SiC has very low friction and does not shed carbon particles, so it suits hot WFI and UPW where faces run with a thin, poorly lubricating film.

How are bioreactor agitator shafts sealed?

Top-entry bioreactors use a hygienic double seal with a sterile gas or condensate barrier so that the vessel stays sealed through SIP. Related: Pharmaceutical · Fermenters & Bioreactors · Beverage & Brewery · Hygienic Double Gas Seal.


Request a Seal Selection

Send the fluid name and concentration, SDS, temperature, suction and discharge pressure, pump make and model, shaft size and speed to info@gipfelengg.com or use our enquiry form. Gipfel Engineering (ISO 9001:2015, NSIC-registered MSME, Mumbai) designs and manufactures mechanical seals, seal support systems and process pumps.

Equipment solutions: Overhung Pumps · Fermenters & Bioreactors · Mixers.

Pump Duty & Mechanical Seal Selection Matrix

Typical values for selection guidance only. Final selection is made against the customer duty sheet and the fluid SDS.

Pump duty Fluid Typical temp. Typical pressure (bar) Seal arrangement Faces / elastomer API piping plan
WFI Loop Pump Water for injection 65–85 °C 3–6 bar Single balanced cartridge, hygienic design SiC vs SiC or diamond-coated SiC / peroxide-cured EPDM; 316L Single seal; no external flush
Purified / Ultrapure Water Pump PW, UPW 18.2 MΩ·cm Ambient–30 °C 3–8 bar Single balanced cartridge, hygienic design SiC vs SiC / EPDM; 316L Single seal; no external flush
Milk / Cream Pump Dairy product 4–80 °C 2–5 bar Single balanced cartridge, hygienic design SiC vs carbon or SiC vs SiC / EPDM Plan 62 water quench on hot duty
Wort / Beer Pump Wort, beer 2–100 °C 2–5 bar Single balanced cartridge, hygienic design SiC vs carbon / EPDM Plan 62 water quench on hot wort
CIP Supply / Return Pump Caustic / acid wash 60–85 °C 3–6 bar Balanced multi-spring cartridge SiC vs SiC / EPDM Single seal
Bioreactor Agitator Sterile culture 30–40 °C; SIP 121–135 °C Vessel pressure Hygienic double gas seal SiC vs SiC / EPDM or FFKM Sterile gas or condensate barrier

Reviewed by Gipfel Engineering’s technical team.

Technical Information Disclaimer

The information on this page, including process descriptions, flow diagrams, operating ranges, seal arrangements, materials and piping plans, is general technical guidance for information only. Values shown are typical industry ranges, not guaranteed ratings or specifications of any Gipfel Engineering product. Each application differs. Seal selection, material compatibility, installation and operation must be verified by qualified personnel against the specific equipment data sheet, process conditions, applicable codes and the pump manufacturer’s instructions. A binding recommendation is given only in a written quotation or technical offer from Gipfel Engineering.

References to standards (such as API 682, ISO 21049, ISO 3069, FDA 21 CFR 177.2600 and NACE MR0175 / ISO 15156) describe common industry practice. They do not mean that any product is certified, qualified or approved to that standard unless this is confirmed in writing for a specific order. Third-party company and product names, including “equivalent to” references, are used for identification only and remain the trademarks of their owners. No affiliation, endorsement or OEM approval is implied.

Compliance with safety, hazardous-area, environmental and statutory requirements at the user’s site remains the responsibility of the plant owner or operator. To the extent permitted by law, Gipfel Engineering accepts no liability for loss or damage arising from reliance on this general information without a confirmed written recommendation. Content may change without notice.

Table of Contents